lasasfetish.blogg.se - Parallel to serial converter wiki

#Parallel to serial converter wiki mod#
#Parallel to serial converter wiki drivers#
#Parallel to serial converter wiki full#
#Parallel to serial converter wiki software#
#Parallel to serial converter wiki Pc#

If you want to use it in unbuffered mode, you do not need to connect the USB cable. When USB cable is connected, the LED will light. PW provides two GND, two 5.0V and two 3.3V outputs. If you connect the power header to a component requires more current, it will damage your USB port. Remember this board utilizes the USB power, which by default only provides 100mA at 5V. With provided flexible jumper wire you can move the pin configuration easily to suit different programmers. Our parallel universal JTAG adapter allows you to easily configure it to be a buffered or unbuffered JTAG. TIAO Multiple Protocol Adapter (JTAG/SPI/I2C/Serial)ĭebrick Wireless Router Using TUMPA and zJTAG What is our universal JTAG adapter? No USB port? no problem, use our USB JTAG: in a nutshell, you need a JTAG cable/adapter is flexible enough to allow you configure it for different softwares/programmers so you only need to invest on one JTAG adapter. Even for the JTAG connector side, there are many different pinouts, 20 pin JTAG, 14 PIN, 12 PIN, 10 PIN etc. which DB25 pin is for TDI? This is really depending on the software, some JTAG softwares may assume TDI is connected to pin 2 of DB25, but others may assume it is on pin 3.

#Parallel to serial converter wiki Pc#

However there is no standard definition on the PC side, e.g. JTAG standard only defines a few hardware pinouts. There are many different JTAG cables available in the market, often they are not compatible to each other.

#Parallel to serial converter wiki mod#

7 Configure it for XBOX 360, so you can mod your 360 to play xbox 360 homebrew emulators.

#Parallel to serial converter wiki software#

6 Configure it to use with Blackcat software for your cable modem (Motorola, Webstar etc.).5 Configure it to use with TJTAG for wireless routers.1 Why you need an universal JTAG adapter?.+3.3V single supply operating voltage range.Compact 64-LD Lead Free LQFP/LQFN package and 56-LD VQFN packages.Extended -40☌ to 85☌ industrial operating temperature range.+1.8V (chip core) and +3.3V I/O interfacing (+5V Tolerant).USB Bulk data transfer mode (512 byte packets in Hi-Speed mode).UHCI/OHCI/EHCI host controller compatible.Supports bus powered, self powered and high-power bus powered USB configurations.Configurable I/O drive strength (4,8,12 or 16mA) and slew rate.Operational configuration mode and USB Description strings configurable in external EEPROM over the USB interface.Auto-transmit enable control for RS485 serial applications using TXDEN pin.UART Interface supports 7/8 bit data, 1/2 stop bits, and Odd/Even/Mark/Space/No Parity.Fully assisted hardware or X-On / X-Off software handshaking.

#Parallel to serial converter wiki full#

Asynchronous serial UART interface option with full hardware handshaking and modem interface signals.

Highly integrated design includes +1.8V LDO regulator for VCORE, integrated POR function and on chip clock multiplier PLL (12MHz – 480MHz).

FT245B-style FIFO interface option with bidirectional data bus and simple 4 wire handshake interface.Enhanced bit-bang Mode interface option with RD# and WR# strobes.Option for transmit and receive LED drive signals on each channel.

#Parallel to serial converter wiki drivers#

FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.

Fast Opto-Isolated serial interface option.

MCU host bus emulation mode configuration option.

CPU-style FIFO interface mode simplifies CPU interface design.

Single channel synchronous FIFO mode for transfers up to 40 Mbytes/sec.

USB to parallel FIFO transfer data rate up to 10Mbyte/sec.

(RS232 Data Rate limited by external level shifter).

RS232/RS422/RS485 UART Transfer Data Rate up to 12Mbaud.

Dual independent UART or FIFO ports configurable using MPSSEs.

Dual Multi-Protocol Synchronous Serial Engine (MPSSE) to simplify synchronous serial protocol (USB to JTAG, I2C, SPI or bit-bang) design.

USB 2.0 High Speed (480Mbits/second) and Full Speed (12Mbits/second) compatible.

No USB specific firmware programming required.

Entire USB protocol handled on the chip.

Single chip USB to dual serial / parallel ports with a variety of configurations.

The FT2232H is available in Pb-free (RoHS compliant) 64-pin LQFP/QFN and 56-pin QVFN packages.īuilding on the innovative features of the FT2232, the FT2232H has two multi-protocol synchronous serial engines (MPSSEs) which allow for communication using JTAG, I2C and SPI on two channels simultaneously.

It has the capability of being configured in a variety of industry standard serial or parallel interfaces. The FT2232H is a USB 2.0 Hi-Speed (480Mb/s) to UART/FIFO IC. The FT2232H is FTDI’s 5th generation of USB devices. With added Power Delivery(PD) functionality to the existing High Speed Series. USB High Speed Power Delivery Series are now available here.